How to Save a Wet Cell Phone Fast

In the presence improvement in technology, there's less risk of phone getting damaged completely by just water, be it cold or hot. So on this post we are going to discuss ways on how to save a wet cell phone fast to start working using various similar method that can be implemented according to phone model and material avialable.

1. What to do with a wet cell phone.
Forasmuch as technology matters, every wet cell phone need to be dried as soon as possible in order to decrease, or rather, avoid damages of small parts of the connection and most importantly, to avoid rusting, which is one of the commonest source of damage that starts with a wet cell phone. In order to save a wet cell phone fast, you need to understand how to avoid rust in order to avoid wrong connection due to broken circuit.

2. Start From Normal drying.
If the phone is still on, switch it off. While many articles from different directories will tell you to strip the phone first, it is also important to start by cleaning the whole body with a clean washcloth. After you've clean the outside, Wrap the phone and shake it to different direction. This is very important as an emergency thought to drain the water that can be drained by shaking. Lets move to the second part on how to save a wet cell phone easily.

3. Stripping the wet cell phone to the minimum.
Remove the battery cover and the battery immediately and Depending on the cell phone model, you can remove some other parts such as back cover, front cover and the keypad.

Blow the area of the headset connector hard about five times. Bit the phone on your hands with a forward motion to let the wet hole of the headset collector to dry. Do the same thing to with the chara connector, microphone, micro USB connector and most importantly, the camera lens and earpiece since they are more fragile to water.

4. Air dry under the sun.
Get a silver plate or anything metalic that can reflect light, and place the parts of the wet cell phone parallel to the direction of the sun. If possible, separate the entire cell phone from other parts ( battery, back cover, battery cover, keypad etc.) in order to make sure your wet cell phone has being dried as quick as possible.

In order to save wet cell phone easily, you need to take proper observation of the time of air or sun dryness in order not to spoil some delicate part of the device. So, place the phone with the screen down. Wait for about 2 hours and turn it over with the screen facing the sun. Since screen is one part of a cell phone that is more fragile to sun and susceptible to getting damage, only leave it for 3 minutes and find a piece of clothing to cover the screen area only. Leave it to last for another 1 hour and 30 minutes before turning it over. Do this for the whole day.

Before fixing the phone or covering the whole parts of the wet cell phone, you need to make sure that your work in getting rid of the wetness has being done correctly. So, put the battery and hold it the way you can on the cell phone. Once it is on, try to navigate to your network connection. If the network is working normal, then you're good to go. Check the speaker, mouthpiece, earpiece, and the charging point to make sure they're working fine. At least by this time, you must have take a well observation of your screen and keypad light to make sure they work also. If everything is working fine, close up everything and use your phone.

In case of obvious remnant of water within the circuit or you're just very skeptical about the lasting function of the cell phone, place it under a bulb for a whole night before you can use it with more assurance the following morning.

Note that using light bulb is also an alternative if you live in an area where sun light and heat are weak. In order to save a wet cell phone, make sure you consider the best and fast means to get it dried before it would last for an hour, making the phone more prone to permanent damage.

5. Lubricating Parts to avoid little rusting.
Researches have shown that cell phone can be rinsed, or rather washed with liquid hydrogen or spirit in order to avoid rusting and to maintain a proper circuit. So using hydrogen or any oil lubricant can be more useful to save a wet cell phone when you have limited sun light to insure proper dryness. Avoid pouring excessive liquid content to avoid screen ink spilage, and to get it dried more faster. So on how to save a wet cell phone fast, putting some brain can be more beneficial.